|
Avago公司的 AEAT-6600是10- 16位可編程無接觸磁旋轉編碼器，工作電壓5V或3.3V，絕對值輸出3線或2線SSI接口模式，絕對值10位到16位分辨率，增量輸出分辨率8-1024CPR，主要用無刷DC馬達的3相轉子，替代電子分解器和電位計，工業自動化和機器人。本文介紹了AEAT-6600主要特性和指標，方框圖以及OTP編程模式和對準模式電路圖，AEAT-6600-T16磁編碼器編程器套件主要特性： AEAT-6600-T16：10 to16-Bit Programmable Angular Magnetic Encoder IC The Avago AEAT-6600 angular magnetic encoder IC is a contact less magnetic rotary encoder for accurate angular measurement over a full turn of 360 degrees. It is a system-on-chip, combining integrated Hall elements, analog front end and digital signal processing in a single device. To measure the angle, only a simple two-pole magnet, rotating over the center of the chip, is required. The magnet may be placed above or below the IC. The absolute angle measurement provides instant indication of the magnet’s angular position with a resolution of 0.005° = 65 536 positions per revolution. This digital data is available as a serial bit stream and as a PWM signal.An internal voltage regulator allows the AEAT-6600 to operate at either 3.3 V or 5 V supplies. AEAT-6600主要特性： 5 V or 3.3 V operation 3-wire or 2-wire SSI interface mode for absolute output Incremental ABI or UVW, and PWM output modes User-programmable zero position, direction & index pulse width Easy magnet alignment with magnetic field strength output and alignment mode  ower-down mode to reduce current consumptionTSSOP-16 IC package RoHS compliant AEAT-6600指標： Absolute 10-bits to 16-bits resolution Incremental output resolutions 8 to 1024 CPR -40℃ to 125℃ operating temperature range AEAT-6600應用： 3-phase commutation for brushless DC motor Resolver and potentiometer replacement Industrial automation and robotics 
圖1。AEAT-6600方框圖
圖2。AEAT-6600 OTP編程模式電路圖
圖3。AEAT-6600 對準模式電路圖
圖3。AEAT-6600-T16 PCB級 應用電路圖 AEAT-6600-T16磁編碼器編程器套件 This user manual describes the Avago HEDS-8937 programmer kit. The AEAT-6600-T16 magnetic encoder programming kit features real-time monitoring and programming of the 32-bit OTP memory within the AEAT-6600-T16 magnetic encoder IC. The HEDS-8937 kit includes the IC interface hardware that is supported by PC software. The IC interface hardware is a microcontroller system that links the AEAT-6600-T16 encoder to the PC through a USB cable. This user manual describes the hardware and PC software setup and gives instructions on PC software operation. AEAT-6600-T16磁編碼器編程器套件主要特性： Bus-powered USB device On-board 6.5 V programming voltage Auto-power off when the AEAT-6600-T16 is removed from the programming socket Read and write the 32-bit OTP memory Real-time monitoring of SSI, PWM, ABI or UVW outputs Real-time monitoring of MAG_HI and MAG_LOW Signals 套件包括： 1. USB cable 2. AEAT-6600-T16 magnetic encoder programmer 3. IC adapter socket 4. 16-pin ribbon cable 5. Installation CD
圖4。AEAT-6600-T16磁編碼器編程器套件外形圖 詳情請見： 
AV02-2792EN DS AEAT-6600-T16 19Jul2011.pdf
(202.28 KB)
AV02-2791EN AN_5501 AEAT-6600 18Jul2011.pdf
(176.1 KB)
|
